Equipment and materials for hydroponics, coco substrate
Barbed adapter 8X1/2" male threaded Designed for connection of 8 mm with accessories female thread 1/2 inch
Barbed coupling 8х8 ммDesigned to connect the tubes 8 мм
BARBED TEE - 8X8X8 ммDesigned to connect the tubes 8 mm
Cap for woodpecker drippers
Recommendation! For proper selection of type plugs please contact us.
Контейнер предназначен для выращивания клубники (земляники садовой) методом гидропоники.
Имеет 11 отверстий для посадки рассады.
Материал — полипропилен.
Использование таких контейнеров позволяют выращивать землянику с оптимальной плотностью посадки, используя при этом минимальный объем субстрата на одно растение, а также обеспечивают хорошую аэрацию, позволяет удобно и эффективно производить уход за растениями, уборку урожая, уменьшает испарение влаги. Ягоды не имеют контакта ни с какими поверхностями, что исключает возможность их механического повреждения, снижает риск появления гнили и др. факторов, которые могут повлиять на качество урожая.
Цена указана для розничных заказов.
Для оптового заказа от 3000 шт - свяжитесь с нами.
Universal pressure-compensating (PC) and compensating non-leakage (CNL) butter dripper with self-flushing operation. Mounted on a PE pipe. Application For greenhouses, nurseries, orchards, landscaping, gardening, vegetables and berries, for pulse irrigation for growing hydroponically, potting, soilless culture. Provides reliable, uniform watering, at areas with a height difference as well. If you purchase a dripper complete with micro drip manifold and drip spikes, be sure to book the connecting pipe diameter 3/5 mm.
Ph meter (ph-01)
Pen-type ph meter
Specification
measure range: 0.00—14.00ph
resolution:0.01ph
accuracy:+/_0.01ph
Automatic temperature compensation: 0°C--60°C
Power supply: 2*1.5V(AG13 battery)
operating temperature: 0°C--60°C
calibration: manual at one point through trimmers
dimension: 155mm*29mm*16mm
weight: 48g
Operation
remove tne protective cap.
first rinse the electrode with distilled water, and suck it with filter paper.
turn the meter on by pressing the on key.
immerse the ph meter electrode in the solution to be tested.
stir gently and wait for the reading to stabilize.
after use. rise the electrode with water to minimize contamination. turn the meter on by pressing the off key.
always replace the protective cap after use.
Calibration
immerse the electrode in PH6.86(under the temperature of 25°C ) standard buffer solution of phosphate, and gently shake the electrode.
regulate the trimmer with a screwdriver until the buffer solution value corresponding to the measurement temperature is obtained.
immerse the electrode in ph 4.01 or ph 9.18 the standard buffer solution of borax.
after about one minute, until the buffer solution value corresponding to the measurement temperature is obtained.
Battery install
If the meter can not be switched on or the display fades, to change batteries, pull out the battery case and replace batteries. Pay attention to the polarity of battery.
Important : the instrument’s ph range must be re-calibrated whenever.
approximately one month has passed from the last calibration.
the electrode has been used in particularly taxing conditions.
the utmost accuracy is required.
Meter TDS & ECSpecificationLarge LCD screenLow power consumptionHigh accuracyLong battery lifemultifunctionalityUseful features:1. The device records the last testimony.2. After 5 minutes the automatic disconnection of the battery to store energy.conductivityTDSDegrees CelsiusAccuracyNWThe size0--9990us / cm0 - 5000ppm0,1 - 80,0 ° C± 2%55g154 * 30 * 14 (mm)Switching between TDS and conductivity:The default output data the TDS, if you want to measure the electrical conductivity of the solution ( EU ), press the SHIFT button.Automatic Temperature Compensation:The device has a function of automatic temperature compensation to the measurement mode.Temperature Output Format:Temperature readings are displayed by default in degrees Celsius. Double-click the SHIFT button to display the temperature in degrees Fahrenheit.Measuring the parameters of the solution:1. Remove the electrode protective cap before use.2. Press the button, place the electrode into the test solution.3. After the readings stabilize, press the button and holding it, remove the device from the solution and read the testimony.4. After reading and disconnection device wipe the electrodes and close the cap.Maintenance:Keep clean the electrodes, cover them with a protective cap for a long period of inactivity, remove the batteries from the device.Note:1. Device - is a professional tool, please operate according to instructions in order to avoid damage to the instrument2. Avoid direct sunlight.3. Use standard calibration buffer solution. Improper calibration will lead to measurement errors.4. Do not immerse the instrument in the test solution is completely in order to avoid short circuits.
Universal inserter UP-N is designed to insert external drippers and plungers in PE pipe with a diameter of 12 mm to 32 mm
Universal punch UP is designed to punch holes for mounting external drippers and plungers in PE pipe with a diameter of 12 mm to 32 mm