Drop1000-1m

$275.00

Set Drop-1000-1м.
Manual drip irrigation system.

Управление поливом

Watering control unit. 1 irrigation zone in manual mode. The control unit is combined with the filter unit.

Product description.

The kit is designed to provide drip irrigation with manual control of an area of ​​1000 to 2000 sq. m (depending on the planting scheme). It allows you to water the entire site at once, in manual mode (note: check the debit of the existing water supply source and its ability to provide the necessary water flow while watering the entire site). The kit comes in the form of fully assembled units, which allows you to quickly and easily assemble the system by connecting it to a water source using an ordinary garden hose or polyethylene pipe with a diameter of 25 mm.

The package includes the standard components and assemblies for the DROP-1000 sets:
Капельная трубка LIN-16

A drip irrigation tube with built-in droppers LIN model with a diameter of 16 mm, with a water flow rate of 1.6 liters per hour for each dropper, a distance between droppers of 30 cm and a wall thickness of 0.25 mm (10 mils).

Tube Specifications:

  • Model: LIN 16-1.6-0.30-0.25 (10mils)
  • Operating pressure 0.3-1.5 atm.
  • Maximum length of 1 line, no more than 90 meters.
  • Service life - up to 3-5 years.


To reduce the weight of the kit for international delivery via EMS airmail, lightweight packaging for a reel with a drip tube is used.

*** On large farms, such a tube is often used as a “disposable” one, but with careful handling it will fully work out the long-term life in it. For more efficient operation, the delivery kit includes repair connectors that allow you to connect pieces of the tube in case of mechanical damage.

Filtration unit with manual flushing.
блок фильтрации

The filtration unit, which is a mandatory component of the irrigation system. It purifies water and protects the irrigation system from clogging. The presence of two filters in each filtration unit and parallel switching on for them allows to increase the total area of ​​the filter elements, reduce pressure losses and increase the total water flow through the filtration system up to 10 cubic meters per hour, and application It is this configuration of the filtration unit that allows you to easily and with minimal time rinse the filtration unit without disassembling the filters, which significantly reduces the time for system maintenance and supports filters clean condition.
The filters included in the package may be disk or mesh - at the option of the customer.

We are constantly improving our irrigation systems and the filtration unit that you receive in the delivery may differ slightly in appearance from the one shown in the photo, but this does not affect its functionality.

The filtration unit can be connected to the water source using polyethylene pipes or flexible reinforced plastic hoses. The filtration unit can also be connected to the water source using a threaded connection. All necessary parts are supplied.

Fitting:

стартконнекторStart connector with tap.

Required for connecting drip irrigation pipes to the main pipe. Start connectors are equipped with taps, allowing, if necessary, enable or disable irrigation on individual lines.

 

 

End caps of drip lines

End caps (line end) are used to drown out the end of each individual drip line.окончание линии

Mounted at the ends of the drip tube.

Why is it a stub and not for example a piece of wire or a rope?

We recommend flushing the drip tubes at least once every 1-2 weeks. Such preventive flushing significantly lengthens the life of the irrigation system and saves you money. At the end of the irrigation season, before you remove the system from your site, the drip tubes must be flushed. The end cap allows you to perform this operation easily and simply, without mechanical damage to the end of the tube.

ремконнектор

Repair Connectors

Repair connectors are used to repair drip irrigation tubes in case of mechanical damage and if you change the configuration or scheme of the irrigation and you need to connect the individual pieces of the tube in one line.

 

Compression connector NL251MКоннектор

It is intended for connection to the filtration and automation unit of the supply and distribution pipelines from a polyethylene pipe or a soft plastic hose. The diameter of the pipes or hoses is 25 mm.  

 

Specification.

Name

Q-ty

Drip tube LIN 16-1,6-0.30-0.25(10mil)

1000 m

Filtration unit

1 pc.

Start connector with crane

50 pcs.

End lines

50 pcs.

Repair connector

10 pcs.

Compression connector NL251M

2 pcs.

 
 

DROP irrigation systems 1000 of all modifications are shipped directly from Israel. Delivery is carried out to any country in the world. Delivery cost is determined by the current tariffs at the time of delivery. 

ATTENTION: Please select the filter option that you want to use for your irrigation system. You can select filters with a filter element from the grid or disk filters.

Drop1000-1m
Drop1000-1m
  • Model:TIF-1000-1M

Available Options

Related Articles

Articles related to this product.
Languages
Russian English Bulgarian Hebrew
Manufacturers
Currencies
Authors